Water Dragon V2 Outlet

-

Our awesome Water Dragon V2 Kit is designed to be mounted conveniently to the factory live well outlet cover on your FishPro Trophy ©, providing the perfect OEM look for the outlet of your custom bilge setup.

Designed for a 19mm ( 3/4") bilge hose, the outlet is perfectly suited for use with the SeaFlo © SFBP1-G1100-14A low profile pump.

The included mounting wedge and quality marine grade stainless steel screws will ensure your pump is securely mounted to the hull of your watercraft in the perfect position.

Your kit will include the wedge mount and screws for your SeaFlo Bilge Pump 

A drilling template to ensure the hole for the outlet is drilled in the correct location every time.

The inner and outer hose outlet fittings complete with 1.5M of SpiralFlex bilge hose connected.

The all new V2 kit now comes with a threaded inner and outer half, no more epoxy required, making installation and replacement quick and easy.

-

Suitable TORX © bit for removing the factory live well outlet cover

-

-

-

-

SeaFlo SFBP1-G1100-14A

-

Depending on your installation you will need an appropriate wiring harness and fuses to suit.

-

-

-

To begin the installation process, first remove the factory installed live well outlet cover by removing the 2x Torx screws indicated by the red arrows below.

Be sure to use the correct sized Torx bit and hand tools only, these may be tight from factory.

-

Next you will remove the factory hose clamp on the live well hose, attached to the cover.

-

-

-

After loosening the hose clamp, gently remove the factory hose from the outlet.

Once you have removed the factory cover from your Ski, it is time to prepare the tools and hardware listed above to complete the install.

Using the drilling template provided in your kit, align the template over the factory quick connect hose fitting, ensuring the shaped edge aligns with the profile of the cover as pictured below

-

-

While holding the template securely in place, carefully drill the pilot hole using the supplied drill bit through alignment hole in the template arrowed above.

-

After drilling the pilot hole, remove the drilling template and using the 20mm step drill provided, carefully drill a 20mm hole through the cover, aligning the step drill with the pilot hole drilled previously.

-

-

-

You are now ready to install the outer part of the outlet fitting.

The new V2 mount is threaded. The outer half with hexagonal profile on the inside threads into the inner half with the hose attached. Using the 3D printed hex wrench, install the shaped ring to the outer half of the outlet and assemble as per the below images. Making sure to align the angle with the cover.

-

-

This guide does not cover the wiring of the switch panel, fuses or auxiliary wiring, if you are unsure on how to do this yourself, please consult your dealer or other suitably qualified individual. OCD accepts no responsibility or liability in this regard.

-

-

The included wedge mount is designed for use with the SeaFlo SFBP1-G1100-14A low profile pump. The wedge is designed to install the pump in front of the auxiliary battery in the FishPro Trophy as pictured below.

-

Start by installing the wedge to the pump as pictured below, using the supplied stainless steel screws.

-

-

Ensure the bilge of your ski is clean and free from oils or other contaminants.

The surface should be dry and clean BEFORE proceeding below.

We recommend using:

-

-

Using the SikaFlex Marine adhesive, apply a bead to the underside of the wedge, ensuring coverage of the entire underside.

You can now install the pump into the ski by gently moving the cooling hoses aside and dropping the pump down between. You can use a large cable tie to hold the factory hoses to one side while you mount the pump if needed. The wedge should locate the pump perfectly level and oriented in the correct place, just ahead of the factory scupper hoses as indicated by the arrow in the below photo.
When securing the pump, the pickup should remain just above the bilge of the ski to allow the filter cover to be removed if needed for cleaning. The clearance to the bilge should be the same distance as the picture above, with the pump mounted to the wedge and sitting on a level surface.

-

-

-

Attach the bilge hose to the pump using the hose clamp (not provided in the kit).

Route the hose to the factory live well outlet hole in the hull of your ski.

The below images show the recommended route for the bilge hose.

-

You are now ready to install the cover back onto your watercraft.

Replace the factory live well hose onto the cover and secure with 2x cable ties as below.

NOTE: The new Water Dragon outlet will not fit through the factory opening in the hull of you use the hose clamp on the love well pipe, cable ties are more than enough to hold the hose to the outlet if appropriately fastened.

Adding an additional cable tie securing the 2x hoses together will provide additional support.

-

-

-

The final step is to feed the hoses back into the ski and install the cover back in place. 

Do not force the hoses back into the ski, if they are getting caught, ensure the cable tie ends are facing towards the inside and gently squeeze the hoses as you push them back through the hole in the hull, this will allow more space for the cable ties to pass through.

-

Finish by re-installing the 2x Torx screws and enjoy your new Water Dragon V2 Outlet.